Run Hardware Diagnostic tests

Most servers are shipped with a hardware diagnostics CD, although other hardware vendors may choose to install a hidden utility partition located on your hard drive.

Note: If you are not experienced with computers or have any concerns, please contact your hardware vendor.

You can diagnose hardware related problems on your server by booting from the diagnostic CD or choosing Diagnostics from the boot device list.

These diagnostic tools allow you to:

• Check the hardware configuration and verify that it is functioning correctly.
• Test individual hardware components.
• Diagnose hardware-related problems.
• Obtain a complete hardware configuration.

When testing, if a component failure is detected, make note of any error code(s) and contact the hardware vendor.

Check your memory

Note: This process requires downtime on your ESX/ESXi host for up to 48 hours. In most cases, contacting your hardware vendor for a diagnostic utility as mentioned above should be sufficient in testing your hardware. VMware does not endorse or recommend any particular third party utility.  However, there are third party options available to test your memory.

To test your memory:

1. Download memtest86+ from http://www.memtest.org/.
2. Extract the ISO image from the .gz or .zip archive.
3. Burn the image to CD.
4. Boot your ESX/ESXi host from the CD.
5. The memtest goes through each memory bank and checks for errors.
   
   Note: If memtest86+ does not run on your hardware, contact your vendor for their memory test utility. 

Ensure your server conforms to Non-Uniform Memory Access (NUMA) rules and regulations

Notes:

• If you are not experienced with computers or have any concerns, please contact your hardware vendor.
• Problems related to NUMA usually occur following a RAM upgrade or after an ESX/ESXi Server host installation.

You might see an error such as the following:

The BIOS reports that NUMA node 1 has no memory. This problem is either caused by a bad BIOS or a very unbalanced distribution of memory modules. 

NUMA is a system where each processor has separate memory. The separate memory helps to avoid a performance hit when several processors attempt to address the same memory.

The main requirement is that a similar amount of memory is installed beside each processor. If the amount of memory installed beside each processor is not not similar, it is unbalanced and you might experience performance problems.For more information, see ESX Server Memory Management on Systems with AMD Opteron Processors (1570).

More information on NUMA is also available in the Resource Management Guide.

Run the VMware CPU Identification Utility

To ensure that your CPU(s) are being detected as expected you can use the VMware CPU Identification Utility. You can download the utility at VMware Shared Utilities. This tool helps you ensure that the ESX host is detecting and reporting your CPU(s) correctly.

When the the VMware CPU Identification Utility has been downloaded, the cpuid.iso image can be used to create a bootable CD that aids in processor and feature identification. The tool displays Family/Model/Stepping information for the CPUs detected, and hexadecimal values for the CPU registers that identify specific CPU features. The hexadecimal register values are then interpreted to indicate whether the CPUs support features like, 64bit, SSE3, and nX/xD.

The following is sample output:

Reporting CPUID for 2 logical CPUs...

All CPUs are identical

Family: 0f Model: 04 Stepping: 1

ID1ECX ID1EDX ID81ECX ID81EDX
0x0000641d 0xbfebfbff 0000000000 0x20100000Vendor : Intel
Processor Cores : 1
Brand String : " Intel(R) Xeon(TM) CPU 2.80GHz"
SSE Support : SSE1, SSE2, SSE3
Supports NX / XD : Yes
Supports CMPXCHG16B : Yes
Hyperthreading : Yes
Supports 64-bit Longmode : Yes
Supports 64-bit VMware : No

Additional Information

In addition make sure that you are meeting the minimum system requirements for your ESX/ESXi.  For more information see Minimum requirements for installing ESX/ESXi (1003661).For more information about decoding machine check exceptions, see  Decoding Machine Check Exception (MCE) output after a purple screen error (1005184)

Basics Trouble shooting on VMware ESX/ESXi

1) What is management service service used for ESX/ESXi Server?
2) What is Watchdog ?
3) What is Host Agent ?

I am not able to create the VM's in  running ESX / ESXi Server, But i have some VM in ESX Server which is Running with out Any issue .

How to Solve this issue ?
[root@server]# service mgmt-vmware restart
Stopping VMware ESX Server Management services:
VMware ESX Server Host Agent Watchdog [ OK ]
VMware ESX Server Host Agent [ OK ]
Starting VMware ESX Server Management services:
VMware ESX Server Host Agent (background) [ OK ]
Availability report startup (background) [ OK ]
[root@server]# service vmware-vpxa restart
Stopping vmware-vpxa: [ OK ]
Starting vmware-vpxa: [ OK ]
[root@server]#

Virtual Networking Features of the VMware vNetwork Distributed Switch and Cisco Nexus 1000V Switches

VMware vNetwork Standard Switch

The VMware vNetwork Standard Switch (vSS) is the base-level virtual networking alternative. It extends the familiar appearance, configuration, and capabilities of the standard virtual switch (vSwitch) in VMware ESX 3.5 to ESX 4.0 and vSphere 4.

VMware vNetwork Distributed Switch

The VMware vNetwork Distributed Switch (vDS) is new with vSphere 4. The VMware vDS extends the feature set of the VMware Standard Switch, while simplifying network provisioning, monitoring, and management through an abstracted, single distributed switch representation of multiple VMware ESX and ESXi Servers in a VMware data center.

Cisco Nexus 1000V Series Switches

Cisco Nexus™ 1000V Series Switches are the result of a Cisco and VMware collaboration building on the VMware vNetwork third-party vSwitch API of VMware vDS and the industry-leading switching technology of the Cisco Nexus Family of switches. Featuring the Cisco NX-OS Software data center operating system, the Cisco Nexus 1000V Series extends the virtual networking feature set to a level consistent with physical Cisco switches and brings advanced data center networking, security, and operating capabilities to the vSphere environment. It provides end-to-end physical and virtual network provisioning, monitoring, and administration with virtual machine–level granularity using common and existing network tools and interfaces. The Cisco Nexus 1000V Series transparently integrates with VMware vCenter Server to provide a consistent virtual machine provisioning workflow while offering features well suited for data center–class applications, VMware View, and other mission-critical virtual machine deployments.

VIRTUAL FEATURE COMPARISION

 

NETWORKING ISSUES COMMANDS FOR VSWITCH,VKERNEL,VSWIF

This command will be use ful for migraton of servers from one network place to another network place , i hope this will be very useful in working scenario...




Networking: Esxcfg-firewall Esxcfg-nics Esxcfg-vswitch Esxcfg-vswif Esxcfg-route Esxcfg-vmknic

Storage: Esxcfg-mpath Esxcfg-nas Esxcfg-swisci Esxcfg-vmhbadevs

General: Esxcfg-advcfg Esxcfg-auth Esxcfg-info Esxcfg-resgrp Esxcfg-upgrade

Boot/Diagnostic: Esxcfg-boot Esxcfg-dumppart Esxcfg-init Esxcfg-linuxnet Esxcfg-module



Esxcfg-firewall

Description: Configures the service console firewall ports

Syntax: esxcfg-firewall
Options:

-q Lists current settings

-q Lists settings for the specified service

-q incoming
outgoing Lists settings for non-required incoming/outgoing ports

-s Lists known services

-l Loads current settings

-r Resets all options to defaults

-e Allows specified service through the firewall (enables)

-d Blocks specified service (disables)

-o
udp,in
out,name> Opens a port

-c
udp,in
out> Closes a port previously opened by –o

-h Displays command help

-allowincoming Allow all incoming ports

-allowoutgoing Allow all outgoing ports

-blockincoming Block all non-required incoming ports (default value)

-blockoutgoing Block all non-required outgoing ports (default value)



Default Services:

AAMClient Added by the vpxa RPM: Traffic between ESX Server hosts for VMware High Availability (HA) and EMC Autostart Manager – inbound and outbound TCP and UDP Ports 2050 – 5000 and 8042 – 8045

activeDirectorKerberos Active Directory Kerberos - outbound TCPs Port 88 and 464

CIMHttpServer First-party optional service: CIM HTTP Server - inbound TCP Port 5988

CIMHttpsServer First-party optional service: CIM HTTPS Server - inbound TCP Port 5989

CIMSLP First-party optional service: CIM SLP - inbound and outbound TCP and UDP Ports 427

commvaultDynamic Backup agent: Commvault dynamic – inbound and outbound TCP Ports 8600 – 8619

commvaultStatic Backup agent: Commvault static – inbound and outbound TCP Ports 8400 – 8403

ftpClient FTP client - outbound TCP Port 21

ftpServer FTP server - inbound TCP Port 21

kerberos Kerberos - outbound TCPs Port 88 and 749

LicenseClient FlexLM license server client - outbound TCP Ports 27000 and 27010

nfsClient NFS client - outbound TCP and UDP Ports 111 and 2049 (0 – 65535)

nisClient NIS client - outbound TCP and UDP Ports 111 (0 – 65535)

ntpClient NTP client - outbound UDP Port 123

smbClient SMB client - outbound TCP Ports 137 – 139 and 445

snmpd SNMP services - inbound TCP Port 161 and outbound TCP Port 162

sshClient SSH client - outbound TCP Port 22

sshServer SSH server - inbound TCP Port 22

swISCSIClient First-party optional service: Software iSCSI client - outbound TCP Port 3260

telnetClient NTP client - outbound TCP Port 23

TSM Backup agent: IBM Tivoli Storage Manager – inbound and outbound TCP Ports 1500

veritasBackupExec Backup agent: Veritas BackupExec – inbound TCP Ports 10000 – 10200

veritasNetBackup Backup agent: Veritas NetBackup – inbound TCP Ports 13720, 13732, 13734, and 13783

vncServer VNC server - Allow VNC sessions 0-64: inbound TCP Ports 5900 – 5964

vpxHeartbeats vpx heartbeats - outbound UDP Port 902



Note: You can configure your own services in the file /etc/vmware/firewall/services.xml



esxcfg-firewall examples:

Enable ssh client connections from the Service Console:

# esxcfg-firewall -e sshClient

Disable the Samba client connections:

# esxcfg-firewall -d smbClient

Allow syslog outgoing traffic:

# esxcfg-firewall -o 514,udp,out,syslog

Turn off the firewall:

# esxcfg-firewall -allowIncoming

# esxcfg-firewall -allowOutgoing

Re-enable the firewall:

# esxcfg-firewall -blockIncoming

# esxcfg-firewall –blockOutgoing

Esxcfg-nics

Description: Prints a list of physical network adapters along with information on the driver, PCI device, and link state of each NIC. You can also use this command to control a physical network adapter’s speed and duplexing.

Syntax: esxcfg-nics [nic]



Options:

-s Set the speed of this NIC to one of 10/100/1000/10000. Requires a NIC parameter.

-d Set the duplex of this NIC to one of 'full' or 'half'. Requires a NIC parameter.

-a Set speed and duplex automatically. Requires a NIC parameter.

-l Print the list of NICs and their settings.

-r Restore the NICs configured speed/duplex settings. (Internal use only)

-h Displays command help



esxcfg-nics examples:

Set the speed and duplex of a NIC (vmnic2) to 100/Full:

esxcfg-nics -s 100 -d full vmnic2

Set the speed and duplex of a NIC (vmnic2) to auto-negotiate:

esxcfg-nics -a vmnic2

esxcfg-vswitch

Description: Creates and updates virtual machine (vswitch) network settings

Syntax: esxcfg-vswitch [vswitch[:ports]]

Options:

-a Add a new virtual switch.

-d Delete the virtual switch.

-l List all the virtual switches.

-L Set pnic as an uplink for the vswitch.

-U Remove pnic from the uplinks for the vswitch.

-p Specify a portgroup for operation. Use ALL for operation to work on all portgroups

-v Set VLAN ID for portgroup specified by -p. 0 would disable the VLAN.

-c Check to see if a virtual switch exists. Program outputs a 1 if it exists, 0 otherwise.

-A Add a new portgroup to the virtual switch.

-D Delete the portgroup from the virtual switch.

-C Check to see if a portgroup exists. Program outputs a 1 if it exists, 0 otherwise.

-r Restore all virtual switches from the configuration file (Internal use only)

-h Displays command help

esxcfg-vswitch examples:

Add a pnic (vmnic2) to a vswitch (vswitch1):

esxcfg-vswitch -L vmnic2 vswitch1

Remove a pnic (vmnic3) from a vswitch (vswitch0):

esxcfg-vswitch -U vmnic3 vswitch0

Create a portgroup (VM Network3) on a vswitch (vswitch1):

esxcfg-vswitch -A "VM Network 3" vSwitch1

Assign a VLAN ID (3) to a portgroup (VM Network 3) on a vswitch (vswitch1):

esxcfg-vswitch -v 3 -p "VM Network 3" vSwitch1


Esxcfg-vswif

Description: Creates and updates service console network settings. This command is used if you cannot manage the ESX Server host through the VI Client because of network configuration issues.

Syntax: esxcfg-vswif [vswif]



Options:

-a Add vswif, requires IP parameters. Automatically enables interface.

-d Delete vswif.

-l List configured vswifs.

-e Enable this vswif interface.

-s Disable this vswif interface.

-p Set the portgroup name of the vswif.

-i or DHCP The IP address for this vswif or specify DHCP to use DHCP for this address.

-n The IP netmask for this vswif.

-b The IP broadcast address for this vswif. (not required if netmask and ip are set)

-c Check to see if a virtual NIC exists. Program outputs a 1 if the given vswif exists, 0 otherwise.

-D Disable all vswif interfaces. (WARNING: This may result in a loss of network connectivity to the Service Console)

-E Enable all vswif interfaces and bring them up.

-r Restore all vswifs from the configuration file. (Internal use only)

-h Displays command help.



Note: You can set the Service Console default gateway by editing the /etc/sysconfig/network file or through the VI Client under Configuration, DNS & Routing.



esxcfg-vswif examples:

Change your Service Console (vswif0) IP and Subnet Mask:

esxcfg-vswif -i 172.20.20.5 -n 255.255.255.0 vswif0

Add a Service Console (vswif0):

esxcfg-vswif -a vswif0 -p "Service Console" -i 172.20.20.40 -n 255.255.255.0

Esxcfg-route

Description: Sets or retrieves the default VMkernel gateway route

Syntax: esxcfg-route [ [] ]

can be specified in 2 ways: as a single argument in / format or as a pair.

is either an IP address or 'default'



Options: -a Add route to the VMkernel, requires network address (or 'default') and gateway IP address.

-d Delete route from the VMkernel, requires network address (or 'default').

-l List configured routes for the Service Console.

-r Restore route setting to configured values on system start. (Internal use only)

-h Displays command help

esxcfg-route examples:

Set the VMkernel default gateway route:

esxcfg-route 172.20.20.1

Add a route to the VMkernel:

esxcfg-route -a default 255.255.255.0 172.20.20.1

Esxcfg-vmknic

Description: Creates and updates VMkernel TCP/IP settings for VMotion, NAS, and iSCSI

Syntax: esxcfg-vmknic [[portgroup]]

Options:

-a Add a VMkernel NIC to the system, requires IP parameters and portgroup name.

-d Delete VMkernel NIC on given portgroup.

-e Enable the given NIC if disabled.

-D Disable the given NIC if enabled.

-l List VMkernel NICs.

-i The IP address for this VMkernel NIC. Setting an IP address requires that the -n option be given in same command.

-n The IP netmask for this VMkernel NIC. Setting the IP netmask requires that the -i option be given in the same command.

-r Restore VMkernel TCP/IP interfaces from configuration file. (Internal use only)

-h Displays command help



esxcfg-vmknic examples:

Add a VMkernel NIC and set the IP and subnet mask:

esxcfg-vmknic -a "VM Kernel" -i 172.20.20.19 -n 255.255.255.0

Installing NETWORK FILE Server

(Note: NFS Server works on Windows 2003 R2 with Service pack 2 & Windows 2008  )

1. On the Windows 2003 Server make sure “Microsoft Services for NFS” in installed. If not you need to add it under Add/Remove Programs, Windows Components, Other Network File and Print Services
2. Next go to folder you want to share and right-click on it and select Properties
3. Click on the NFS Sharing tab and select “Share this Folder”
4. Enter a Share Name, check “Anonymous Access” and make sure the UID and GID are both .
5. In Virtual Center, select your ESX server and click the “Configuration” tab and then select “Storage”
6. Click on “Add Storage” and select “Network File System” as the storage type
7. Enter the Windows Server name, the folder (share) name and a descriptive Data store Name
8. Once it finishes the configuration you can now map your VM’s CD-ROM devices to this new VMFS volume
Note: It is assumed that you have already installed Active Directory and DNS with the correct configuration.
Open the Control Panel and then start the Add/Remove Programs utility. After it has started select from the left panel “Add/Remove Windows Components.”

This will open a new panel. A list of components will be presented. Those components that already have a checkmark in the box at their left are already installed. Scroll down until you find the entry for ‘Other Network File and Print Services.’ (Why NFS is lumped in with Print Services is unknown, but this arrangement does change with the next Server release.)

Now select the Details button. A new window will open titled “Other Network File and Print Services.”

From this Window choose “Microsoft Services for NFS” and choose Details again. Yet another window will open, showing all of the available components related to NFS, titled ‘Microsoft Services for NFS.’

In the ‘Microsoft Services for NFS’ window you will select all of the components that you need to support your local configuration. You should check all of the available selection boxes in a typical situation because all of these components will be needed. If you are not going to use UNM because all of your client machines are now Windows Vista then you won’t need to select User Name Mapping. Once all of the choices are made, click on OK (several times) to begin the installation/activation.

window7 Updates

Windows updates may fail in Windows 7 or in Vista with the Error Code 0×80070422 with the following error in the c:\windows\logs\CBS\CBS.log file.

80070422 SelfUpdate Failure Software Synchronization Windows Update Client failed to detect with error 0×80070422

This can happen for two reasons,

•“Windows Update” Service is disabled or not set to Automatic as Startup Type

•“Windows Modules Installer” Service is not set to manual as Startup type.

To resolve this Windows Vista or Windows 7 update issue, set the Startup type of respective services to “Automatic” & “Manual” respectively.

Follow the steps to resolve Windows Update error 80070422:

                        Important:You must be logged on as an administrator to perform these steps.
•Press Start, type admin in the start menu search box, and click on Administrative Tools
•Double-click Services. If you are prompted for an administrator password or confirmation, type the password or provide confirmation
•Right-click the Windows Update service, and then click Properties
•On the General tab, next to Startup type, make sure that Automatic is selected
•Next to Service status, check to see if the service is started. If it is not, click Start. If you are prompted for an administrator password or confirmation, type the password or provide confirmation.
•Similarly, set the “Windows Modules Installer” service startup type as “manual”.
Note:First you want to reveal the hidden admin account in Windows Vista and login to the hidden admin account.For this do the following:
•Click on Windows Vista Start orbs.
•In start menu search type: cmd
•Right-Click the cmd icon and choose “Run as Administrator”
•Now type the follwoing command:
net user administrator /active:yes
You should see a message that the command completed successfully, logoff and login to the true admin account

Updates Error In windows Operating System

I understand the inconvenience you encountered when trying to perform Windows Update. Please be assured that I will do my best to help you.


The issue may be caused by one of the following factors:
1. The installation is affected by some third-party security software.
2. The downloaded installation file is corrupted.


In order to narrow down the cause of our issue, let's refer to the following steps:

NOTE: Some third party programs can affect the Windows Update service. If you are running any third party applications such as Spyblocker, Internet or web accelerators (programs designed to boost the speed of the Internet connection), security or anti-virus programs (Norton, McAfee, etc.), I recommend we temporarily disable or shut them down and then try accessing Windows Update later. Please be sure to enable them again when the update process has been completed.


Step 1: Rename the Windows Update Softwaredistribution folder
================================================
This issue may occur if the Windows Update Software distribution folder has been corrupted. We can refer to the following steps to rename this folder. Please note that the folder will be re-created the next time we visit the Windows Update site.
1. Close all the open windows.
2. Click the "Start" Button, click "All programs", and click "Accessories".
3. Right-click "Command Prompt", and click "Run as administrator".

4. In "Administrator: Command Prompt" window, type in "net stop WuAuServ" (without the quotes) and press Enter.
Note: Please look at the cmd window and make sure it says that it was successfully stopped before we try to rename the folder. However, if it fails, please let me know before performing any further steps and include any error messages you may have received when it failed.

5. Click the "Start" Button, in the "Start Search" box, type in "%windir%" (without the quotes) and press Enter.
6. In the opened folder, look for the folder named "SoftwareDistribution".
7. Right-click on the folder, select "Rename" and type "SDold" (without the quotes) to rename this folder.
8. Still in "Administrator: Command Prompt" window, type the command "net start WuAuServ" (without the quotes) in the opened window to restart the Windows Updates service.

Note: Please look at the cmd window and make sure it says that it was successfully started. However, if it fails, please let me know before performing any further steps and include any error messages you may have received when it failed.
If the steps above do not work, let's refer to the following steps to manually download and install the update.
Step 2: Download and install the update manually.
======================================
1. Please download the update from
http://www.microsoft.com/downloads/details.aspx?displaylang=en&FamilyID=c0145563-428e-47b6-b245-b59dce88ac0e
Please note its location.
2. Please double-click the downloaded file to install the update.
If an error is encountered when installing the update manually, please capture a screenshot for further research
How to capture a screenshot
======================
1. Press the Print Screen key (PrtScn) on your keyboard.
2. Click the "Start" Button, type "mspaint" in the Search Bar and Press Enter.
3. In the Paint program, click the "Edit" menu, click "Paste". Then click the "File" menu, and click "Save".
4. The "Save As" dialogue box will appear. Type a file name in the "File name:" box, for example: "screenshot".
5. Make sure "JPEG (*.JPG;*.JPEG;*.JPE;*.JFIF)" is selected in the "Save as type" box, click "Desktop" on the left pane and then click "Save".
In the meantime, to clarify the issue and provide more accurate troubleshooting steps, please assist me in collecting the following information.


How to collect the WindowsUpdate.log file
================================
1. Click the "Start" Button, type "WindowsUpdate.log" (without the quotes) in the Search Bar and Press Enter. We will see a file named "WindowsUpdate.log"
2. Now click on the "File" menu and then click on the "Save As".

3. From the left panel, click "Desktop" and click the Save button.
Cool........................................................
Contact:Satishchirala@gmail.com

Windows 7 & Vista Updates Errors

Many people having problem with online updates , in windows 7& Vista having some problem for online updating, if updating is not done perfectly virus will come automatically & system performance may decrease,and some software won't work without updates....


I have some solutions to solve this problems (Note: Uninstall Google updater or any Google tools except G talk,Chrome)

Download Patches for windows7 & Vista & XP
 Sytem perfomance is down             http://dl.dropbox.com/u/1823898/Mats_Run.performance.exe
Maintainence problem                     http://dl.dropbox.com/u/1823898/Mats_Run.maintenance.exe
Printing problem                             http://dl.dropbox.com/u/1823898/Mats_Run.printing.exe
Dvd& Cd is not working       http://dl.dropbox.com/u/1823898/Mats_Run.dvd.exe  
Audio Recording                             http://dl.dropbox.com/u/1823898/Mats_Run.AudioRecording.exe
Audio Playback                              http://www.blogger.com/%20%20http://dl.dropbox.com/u/1823898/Mats_Run.AudioPlayback.exe%20%20%20
i had done this before writing the blog ...keep go on doing this ...
Have a Nice Day ()()()()()()()

MICROSOFT OUTLOOK ERROR "cannot start microsoft outlook cannot open the outlook window 2010"

Hey many of you got this problem ,There is a small procedure below for solving this issue

go to run.........& type "Outlook.exe /resetnavpane"

say ok!!!

Outlook will be opened

if not  run this below site

The way to fix this is to do a system restore.
Below is a link to those instructions.

http://support.microsoft.com/kb/936212/

While the "broken profile" part of this post belongs in the Vista forum.
I'm going to suggest that you pop over to the Office forum for the Outlook part. That is more appropriate for them to handle.
Hope this helped!

http://www.microsoft.com/office/community/en-us/flyoutoverview.mspx

Ports and Protocols of systems

The Windows server system includes a comprehensive and integrated infrastructure that is designed to meet the requirements of developers and of information technology (IT) professionals. This system is designed to run programs and solutions that information workers can use to obtain, to analyze, and to share information quickly and easily. These Microsoft client, server and server program products use a variety of network ports and protocols to communicate with client systems and with other server systems over the network. Dedicated firewalls, host-based firewalls, and Internet Protocol security (IPsec) filters are other important components that are required to help secure your network. However, if these technologies are configured to block ports and protocols that are used by a specific server, that server will no longer respond to client requests.

Ports and Protocols
The following table summarizes the information from the "System Services Ports" section of this article. This table is sorted by port number instead of by the service name.

Protocol / Port - Application protocol - System service name
Protocol 47 - GRE - GRE (IP protocol 47) Routing and Remote Access
Protocol 50 - ESP - IPsec ESP (IP protocol 50) Routing and Remote Access
Protocol 51 - n/a AH IPsec AH (IP protocol 51) Routing and Remote Access
TCP Port 7 - Echo Simple TCP/IP Services
UDP Port 7 - Echo Simple TCP/IP Services
TCP Port 9 - Discard Simple TCP/IP Services
UDP Port 9 - Discard Simple TCP/IP Services
TCP Port 13 - Daytime Simple TCP/IP Services
UDP Port 13 - Daytime Simple TCP/IP Services
TCP Port 17 - Quotd Simple TCP/IP Services
UDP Port 17 - Quotd Simple TCP/IP Services
TCP Port 19 - Chargen Simple TCP/IP Services
UDP Port 19 - Chargen Simple TCP/IP Services
TCP Port 20 - FTP default data FTP Publishing Service
TCP Port 21 - FTP control FTP Publishing Service
TCP Port 21 - FTP control Application Layer Gateway Service
TCP Port 23 - Telnet Telnet
TCP Port 25 - SMTP Simple Mail Transfer Protocol
UDP Port 25 - SMTP Simple Mail Transfer Protocol
TCP Port 25 - SMTP Exchange Server
UDP Port 25 - SMTP Exchange Server
TCP Port 42 - WINS Replication Windows Internet Name Service
UDP Port 42 - WINS Replication Windows Internet Name Service
TCP Port 53 - DNS DNS Server
UDP Port 53 - DNS DNS Server
TCP Port 53 - DNS Internet Connection Firewall/Internet Connection Sharing
UDP Port 53 - DNS Internet Connection Firewall/Internet Connection Sharing
UDP Port 67 - DHCP Server DHCP Server
UDP Port 67 - DHCP Server Internet Connection Firewall/Internet Connection Sharing
UDP Port 69 - TFTP Trivial FTP Daemon Service
TCP Port 80 - HTTP Windows Media Services
TCP Port 80 - HTTP World Wide Web Publishing Service
TCP Port 80 - HTTP SharePoint Portal Server
TCP Port 88 - Kerberos Kerberos Key Distribution Center
UDP Port 88 - Kerberos Kerberos Key Distribution Center
TCP Port 102 - X.400 Microsoft Exchange MTA Stacks
TCP Port 110 - POP3 Microsoft POP3 Service
TCP Port 110 - POP3 Exchange Server
TCP Port 119 - NNTP Network News Transfer Protocol
UDP Port 123 - NTP Windows Time
UDP Port 123 - SNTP Windows Time
TCP Port 135 - RPC Message Queuing
TCP Port 135 - RPC Remote Procedure Call
TCP Port 135 - RPC Exchange Server
TCP Port 135 - RPC Certificate Services
TCP Port 135 - RPC Cluster Service
TCP Port 135 - RPC Distributed File System
TCP Port 135 - RPC Distributed Link Tracking
TCP Port 135 - RPC Distributed Transaction Coordinator
TCP Port 135 - RPC Event Log
TCP Port 135 - RPC Fax Service
TCP Port 135 - RPC File Replication
TCP Port 135 - RPC Local Security Authority
TCP Port 135 - RPC Remote Storage Notification
TCP Port 135 - RPC Remote Storage Server
TCP Port 135 - RPC Systems Management Server 2.0
TCP Port 135 - RPC Terminal Services Licensing
TCP Port 135 - RPC Terminal Services Session Directory
UDP Port 137 - NetBIOS Name Resolution Computer Browser
UDP Port 137 - NetBIOS Name Resolution Server
UDP Port 137 - NetBIOS Name Resolution Windows Internet Name Service
UDP Port 137 - NetBIOS Name Resolution Net Logon
UDP Port 137 - NetBIOS Name Resolution Systems Management Server 2.0
UDP Port 138 - NetBIOS Datagram Service Computer Browser
UDP Port 138 - NetBIOS Datagram Service Messenger
UDP Port 138 - NetBIOS Datagram Service Server
UDP Port 138 - NetBIOS Datagram Service Net Logon
UDP Port 138 - NetBIOS Datagram Service Distributed File System
UDP Port 138 - NetBIOS Datagram Service Systems Management Server 2.0
UDP Port 138 - NetBIOS Datagram Service License Logging Service
TCP Port 139 - NetBIOS Session Service Computer Browser
TCP Port 139 - NetBIOS Session Service Fax Service
TCP Port 139 - NetBIOS Session Service Performance Logs and Alerts
TCP Port 139 - NetBIOS Session Service Print Spooler
TCP Port 139 - NetBIOS Session Service Server
TCP Port 139 - NetBIOS Session Service Net Logon
TCP Port 139 - NetBIOS Session Service Remote Procedure Call Locator
TCP Port 139 - NetBIOS Session Service Distributed File System
TCP Port 139 - NetBIOS Session Service Systems Management Server 2.0
TCP Port 139 - NetBIOS Session Service License Logging Service
TCP Port 143 - IMAP Exchange Server
UDP Port 161 - SNMP SNMP Service
UDP Port 162 - SNMP Traps Outbound SNMP Trap Service
TCP Port 389 - LDAP Server Local Security Authority
UDP Port 389 - LDAP Server Local Security Authority
TCP Port 389 - LDAP Server Distributed File System
UDP Port 389 - LDAP Server Distributed File System
TCP Port 443 - HTTPS HTTP SSL
TCP Port 443 - HTTPS World Wide Web Publishing Service
TCP Port 443 - HTTPS SharePoint Portal Server
TCP Port 443 - RPC over HTTP Exchange Server 2003
TCP Port 445 - SMB Fax Service
TCP Port 445 - SMB Print Spooler
TCP Port 445 - SMB Server
TCP Port 445 - SMB Remote Procedure Call Locator
TCP Port 445 - SMB Distributed File System
TCP Port 445 - SMB License Logging Service
TCP Port 445 - SMB Net Logon
TCP Port 464 - Kerberos Password V5 Net Logon
UDP Port 500 - IPsec ISAKMP Local Security Authority
TCP Port 515 - LPD TCP/IP Print Server
TCP Port 548 - File Server for Macintosh File Server for Macintosh
TCP Port 554 - RTSP Windows Media Services
TCP Port 563 - NNTP over SSL Network News Transfer Protocol
TCP Port 593 - RPC over HTTP endpoint mapper Remote Procedure Call
TCP Port 593 - RPC over HTTP Exchange Server
TCP Port 636 - LDAP SSL Local Security Authority
UDP Port 636 - LDAP SSL Local Security Authority
TCP Port 993 - IMAP over SSL Exchange Server
TCP Port 995 - POP3 over SSL Exchange Server
TCP Port 1067 - Installation Bootstrap Service Installation Bootstrap protocol server
TCP Port 1068 - Installation Bootstrap Service Installation Bootstrap protocol client
TCP Port 1270 - MOM-Encrypted Microsoft Operations Manager 2000
TCP Port 1433 - SQL over TCP Microsoft SQL Server
TCP Port 1433 - SQL over TCP MSSQL$UDDI
UDP Port 1434 - SQL Probe Microsoft SQL Server
UDP Port 1434 - SQL Probe MSSQL$UDDI
UDP Port 1645 - Legacy RADIUS Internet Authentication Service
UDP Port 1646 - Legacy RADIUS Internet Authentication Service
UDP Port 1701 - L2TP Routing and Remote Access
TCP Port 1723 - PPTP Routing and Remote Access
TCP Port 1755 - MMS Windows Media Services
UDP Port 1755 - MMS Windows Media Services
TCP Port 1801 - MSMQ Message Queuing
UDP Port 1801 - MSMQ Message Queuing
UDP Port 1812 - RADIUS Authentication Internet Authentication Service
UDP Port 1813 - RADIUS Accounting Internet Authentication Service
UDP Port 1900 - SSDP SSDP Discovery Service
TCP Port 2101 - MSMQ-DCs Message Queuing
TCP Port 2103 - MSMQ-RPC Message Queuing
TCP Port 2105 - MSMQ-RPC Message Queuing
TCP Port 2107 - MSMQ-Mgmt Message Queuing
TCP Port 2393 - OLAP Services 7.0 SQL Server: Downlevel OLAP Client Support
TCP Port 2394 - OLAP Services 7.0 SQL Server: Downlevel OLAP Client Support
UDP Port 2460 - MS Theater Windows Media Services
UDP Port 2535 - MADCAP DHCP Server
TCP Port 2701 - SMS Remote Control (control) SMS Remote Control Agent
UDP Port 2701 - SMS Remote Control (control) SMS Remote Control Agent
TCP Port 2702 - SMS Remote Control (data) SMS Remote Control Agent
UDP Port 2702 - SMS Remote Control (data) SMS Remote Control Agent
TCP Port 2703 - SMS Remote Chat SMS Remote Control Agent
UPD Port 2703 - SMS Remote Chat SMS Remote Control Agent
TCP Port 2704 - SMS Remote File Transfer SMS Remote Control Agent
UDP Port 2704 - SMS Remote File Transfer SMS Remote Control Agent
TCP Port 2725 - SQL Analysis Services SQL Analysis Server
TCP Port 2869 - UPNP Universal Plug and Play Device Host
TCP Port 2869 - SSDP event notification SSDP Discovery Service
TCP Port 3268 - Global Catalog Server Local Security Authority
TCP Port 3269 - Global Catalog Server Local Security Authority
UDP Port 3343 - Cluster Services Cluster Service
TCP Port 3389 - Terminal Services NetMeeting Remote Desktop Sharing
TCP Port 3389 - Terminal Services Terminal Services
UDP Port 3527 - MSMQ-Ping Message Queuing
UDP Port 4011 - BINL Remote Installation
UDP Port 4500 - NAT-T Local Security Authority
TCP Port 5000 - SSDP legacy event notification SSDP Discovery Service
UDP Port 5004 - RTP Windows Media Services
UDP Port 5005 - RTCP Windows Media Services
TCP Port 6001 - Information Store Exchange Server 2003
TCP Port 6002 - Directory Referral Exchange Server 2003
TCP Port 6004 - DSProxy/NSPI Exchange Server 2003
TCP Port 42424 - ASP.Net Session State ASP.NET State Service
TCP Port 51515 - MOM-Clear Microsoft Operations Manager 2000